## Booting kernel from Legacy Image at 01000000 ... Image Name: NetBSD/evbppc 6.99.10 (INSTALL_ Image Type: PowerPC NetBSD Kernel Image (gzip compressed) Data Size: 2775821 Bytes = 2.6 MiB Load Address: 00020000 Entry Point: 00020000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Transferring control to NetBSD stage-2 loader (at address 00020000) ... initppc(0x20000, 0x6a8000, 0x1fe2dfbc, 0x0, 0x1ff8068c, 0x1fe31a10) porpllsr=0x44441448 sys_clk=66666667 comcnfreq=266666668 openpic-reset(ctpr=15) cache(DC=32KB/32,IC=32KB/32) bptr=8001ffff memprobe=512MB e500_tlbinit(0x6a8000,512MB) hid0=0x80004000/0x80804000 hid1=0x44003040 pordevsr=0xa710847 devdisr=0x13480000 msgbuf=0x1fffd000 exception_init=0x2b3e20 kv_nsegtabs=0x38 kv_segtabs=0x6a8000 uvm_page_physload(0x6e0,0x1fffc,0x6e0,0x1fffc,0)powerpc_fixup_stubs: 781 fixups done in 645193 cycles initppc done! Loaded initial symtab at 0x318810, strtab at 0x3445fc, # entries 11131 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 6.99.10 (TWRP1025-$Revision: 1.5 $) total memory = 512 MB avail memory = 495 MB Found MP boot page @ 0x1ffff000. Spin-up table @ 0x1ffff280 cprng kernel: WARNING insufficient entropy at creation. mainbus0 (root) cpunode0 at mainbus0 node 0 cpunode0: 256KB/32B 4-banked 8-way unified L2 cache cpu0 at cpunode0 instance 1 cpu0: 533 MHz P1025 1.1 with an e500v2 5.1 core, ID 0 (Primary) cpu0: 32KB/32B 8-way L1 data cache cpu0: 32KB/32B 8-way L1 instruction cache cpu0: 2 TLBs, 3 concurrent 8-bit PIDs (256 total) cpu0: tlb0: 512 fixed-size (4KB) 4-way set associative entries cpu0: tlb1: 16 variable-size (4KB..4GB) fully associative entries cpu at cpunode0 instance 2 not configured e500wdog0 at cpunode0: default period is 9 seconds (wdog is active) duart0 at cpunode0: 2 ports com0 at duart0 port 1: ns16550a, working fifo com0: console com1 at duart0 port 2: ns16550a, working fifo duart0: interrupting on irq 26 mdio0 at cpunode0 instance 1 tsec0 at cpunode0 instance 1 mdio 0 phy 2 tsec0: Ethernet address 00:04:9f:02:25:72 atphy0 at mdio0 phy 2: Atheros AR8035 10/100/1000 PHY, rev. 2 atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseSX-FDX, 1000baseT-FDX, auto mdio at cpunode0 instance 2 not configured tsec at cpunode0 instance 2 not configured mdio at cpunode0 instance 3 not configured tsec1 at cpunode0 instance 3 mdio 0 phy 1 tsec1: Ethernet address 00:04:9f:02:25:74 atphy1 at mdio0 phy 1: Atheros AR8035 10/100/1000 PHY, rev. 2 atphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseSX-FDX, 1000baseT-FDX, auto diic0 at cpunode0: 2 ports iic0 at diic0: I2C bus iic1 at diic0: I2C bus diic0: interrupting on irq 27 gpio at cpunode0 not configured ddrc0 at cpunode0: ECC disabled obio0 at cpunode0: 2 of 8 ports enabled obio0: cs0: 64MB 16-bit GPCM region at 0xec000000 obio0: cs2: 1MB 16-bit GPCM region at 0xe0000000 cfi0 at obio0 cs 0 addr 0xec000000 size 0x4000000 cfi0: CFI NOR flash 64 MB x8/x16 nor0 at cfi0 nor0: page size: 64, spare size: 0, block size: 128 KB nor0: LUN size: 512 blocks, LUNs: 1, total storage size: 64 MB flash0 at nor0: NOR flash partition size 64 MB, offset 0 flash0: erase size 128 KB bytes, write size 64 bytes pq3pcie0 at cpunode0 instance 1: PCI-Express x1 controller pci0 at pq3pcie0 bus 0 ppb0 at pci0 dev 0 function 0: Freescale Semiconductor P1025 (rev. 0x11) ppb0: not configured by system firmware pq3pcie1 at cpunode0 instance 2: PCI-Express x1 controller pci1 at pq3pcie1 bus 0 ppb1 at pci1 dev 0 function 0: Freescale Semiconductor P1025 (rev. 0x11) ppb1: not configured by system firmware ehci0 at cpunode0 instance 1: USB controller ehci0: interrupting on irq 12 usb0 at ehci0: USB revision 2.0 spi at cpunode0 not configured sdhc0 at cpunode0: SDHC controller sdhc0: interrupting on irq 56 sdhc0: SD Host Specification 2.0, rev.18 sdmmc0 at sdhc0 slot 0 cpunode0: gpio[a]: 32 input/output/opendrain pins gpio0 at cpunode0: 32 pins cpunode0: gpio[b]: 31 input/output/opendrain pins gpio1 at cpunode0: 32 pins cpunode0: gpio[c]: 32 input/output/opendrain pins gpio2 at cpunode0: 32 pins uhub0 at usb0: vendor 0x0000 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 ld0 at sdmmc0: ld0: 15279 MB, 7760 cyl, 64 head, 63 sec, 512 bytes/sect x 31291392 sectors ld0: 4-bit width, bus clock 25.000 MHz uhub1 at uhub0 port 1: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/77.63, addr 2 uhub1: single transaction translator cprng sysctl: WARNING insufficient entropy at creation. root on md0a dumps on md0b mountroot: trying nfs... mountroot: trying msdos... mountroot: trying lfs... mountroot: trying ext2fs... mountroot: trying ffs... root file system type: ffs WARNING: no TOD clock present WARNING: using filesystem time WARNING: CHECK AND RESET THE DATE! init: copying out flags `-s' 3 init: copying out path `/sbin/init' 11